If you’re looking for a Coilover setting that will give you the height adjustment you need, start by measuring from the Coilover point to your desired height To get the perfect Coilover setting for your car, start by measuring from the Coilover point to the desired height.
Be safe when adjusting your coilovers – if something goes wrong, you don’t want anything coming loose on the road. Finally, adjust your suspension as needed so that you can enjoy a smooth ride every time you hit the open road.
How To Adjust Bc Coilovers Height?
The rear shocks and springs of many vehicles that coilovers are designed for have separate designs due to OEM specifications. The spring load and preload are used to adjust the ride height. The shock is then adjusted to the correct length.
When your Coilover has other, more purposeful adjustments meant specifically for the overall height, you may not want to use the locking collar to adjust ride height minutely, on a linear spring rate.
Disclaimer
Coilovers manufactured by BC are only designed and intended for use on off-road surfaces.
Some local, state and federal regulations may not allow the use of this product on public roads. There may be an impact on vehicle insurance coverage if the product is installed and used.
Consumers are responsible for complying with regulations and policies before operating vehicles on public roads. Make sure you check your local laws and research the parts you wish to purchase before purchasing them.
Find BC Coilover Setting
There are a few ways to adjust the height of your bc coilovers. You can use a wrench to loosen or tighten the top nut on the hinge arm, and then rotate the arm up or down as needed.
Another option is to remove and replace the upper shock absorber assembly (if you have one). You will need a 13mm socket and an Allen wrench for this part If neither of those solutions works, you may need to take your car to a mechanic who can set your coils properly using their torque wrenches and other tools.
Be sure to read your owner’s manual before trying any of these adjustments.
Measure From Coilover Point To Desired Height
To adjust the height of your BC coilovers, measure from the Coilover point to the desired height. Some vehicles come with pre-installed length spacers that can be adjusted easily using a wrench or socket set.
If you don’t have any spacers available, then you will need to remove your wheel and use a ruler to measure how much space needs to be created between each strut assembly in order for the suspension system to function properly.
Once you know how much space there is between each strut assembly, reattach your wheel and tighten all four bolts on each side of the strut tower until it makes contact with the spacer (do not over torque).
Finally, level your car by adjusting both front and rear camber angles using a camber gauge or turning knuckles.
Multiply By 2 And Use As Adjustment Value
To adjust your BC coilovers height, multiply by 2 and use as the adjustment value. This will ensure that you are getting the perfect suspension system for your car’s needs.
Be sure to check your car’s owner’s manual to find out how to adjust the height of these coils. Use a level when adjusting them so that they remain in a straight line while driving; this will help with stability and safety during travel or racing conditions.
Always remember to consult your BC Coilover manufacturer’s instructions before making any adjustments.
Screw In Both Bolts Until They Are Tight – Do Not Over-tighten
Make sure the car is level before you adjust the coilovers. Tighten both bolts until they are tight, but do not over-tighten them. If your car is still dented after adjusting the coilovers, it may need to be taken in for repair or replaced altogether.
Adjusting your Coilover height will affect how much suspension travel and ride height you have when driving on uneven surfaces or bumps; take this into consideration before making any adjustments.
When tightening down each bolt make sure that there isn’t too much slack in either of the adjustment wires – if there is, use a wrench to tighten one side at a time until each wire has equal tension.
Be Safe When Adjusting Your Coilovers
Always adjust your coilovers by slowly and safely lowering them until they are at the desired height. If you find that your coilovers are too low or high, it may be necessary to adjust them again using a different method.
Never tighten or loosen the adjusting bolts excessively; doing so can cause damage to your suspension system and/or vehicle. Be aware of potential obstructions while adjusting your coil overs, as they can easily cause injury if not avoided properly.
Finally, always consult with an expert in order to achieve optimal performance from your Coilover System.
What is the drop for BC coilovers?
BC Coilovers offer an inch more drop than standard setups, allowing for a lower car by 5″ to 1″ at their highest adjustment. Standard setups can then drop down to 3″ to 4″ lower than stock at the maximum drop setting.
The higher the BC coil-overs adjustment, the less dropped you’ll get; starting from 3″. BC Coilovers are custom built for each vehicle and may require some additional mods (such as lowering your ride height) in order to work with them.
Once you have determined how much of a lowered stance you desire, consult with a professional who will be able to give you accurate measurements and advice on what setup would best suit your needs.
How high can you raise BC coil overs?
If you are looking for a more performance-oriented ride, then you may want to consider BC coil overs. These springs come with a height adjustment range of 1-3″, which makes setup much easier.
The default ride height is the shortest spring possible in order to make setup easier, but you can raise it above or below this if needed. You will need to purchase additional parts if your vehicle’s OEM springs are too tall/short; however, BC coils over can be ridden at any height above or below the default setting.
Can coilovers be adjusted to stock ride height?
When adjusting your coilovers, you can lengthen or shorten the spring to adjust ride height. To raise the car, you will need to lengthen the Coilover springs; to lower the car, you will shrink the length of the coils and adjust collars A and B accordingly.
You don’t have to remove the spindle mount in order to change these settings – just make sure they are tightened against each other before doing so.
Checking spring rates is always a good idea when making any adjustments – this way you’ll know exactly how much tension is needed for your vehicle’s suspension system.
Always consult with a professional if you’re not familiar with working on your own Coilovers.
To Recap
If you have a set of Bc Coilovers and want to adjust their height, there are a few simple steps that you can take. First, loosen the two screws located at the top of each Coilover cup.
Next, slide the screw on one cup up or down until it lines up with the corresponding screw on the other cup. Finally, tighten both screws to your desired height.
Leave a Reply