Generally, P1361 means a problem with the TDC Sensor on a Honda Accord. Faulty connections usually cause this problem. There is a problem with the TDC Sensor (also known as the Camshaft Position Sensor) if this code appears.
The vehicle will stall if this sensor has an intermittent fault. You should be able to solve your problem by replacing this sensor. The code is one of the most commonly encountered OBD2 trouble codes.
You can find more information about what it means, how to fix it, and what other codes may be related to it in the article below.
P1361 Honda Code Definition: Top Dead Center Sensor 1 Intermittent Interruption
Crankshaft Position (CKP) Sensors help determine engine speed, fuel injection timing, and ignition timing for each cylinder.
In addition to measuring ignition timing at start-up (cranking), the Top Dead Center (TDC) Sensor also determines the crank angle when it is abnormal. To inject fuel sequentially into each cylinder, the Cylinder Position (CYP) Sensor detects the location of cylinder No. 1.
Understanding Honda Accord P1361 Code
Specifically, the P1361 code occurs when Honda’s PCM/ECM detects intermittent interruptions in the TDC sensor, which causes the PCM/ECM to exhibit a diagnostic trouble code.
A sensor like this is integral to the ignition timing system that ensures the car runs well. It will affect your ability to accelerate quickly and produce less power than you would normally have if this weren’t working.
There must be a starting point because the engine’s internal components must function together. Known as the Top Dead Center (TDC), it is maintained by the Top Dead Center Sensor in newer vehicles.
Failure to fix this will result in damage to your engine, which will turn into a major repair that would be very expensive. Don’t ignore this, as it shouldn’t cost you more than a couple of hundred dollars to have it repaired.
What Are The Possible Symptoms Of Code P1361 Honda?
- The engine light is illuminated (or a warning that the engine needs to be serviced)
- Performance issues with the engine
Make sure the wiring insulation is intact, and look first for obvious issues like corrosion and cuts. Check all the connectors and wiring for voltage drop, continuity, and resistance using a multimeter.
Honda Accord P1361 DTC code diagnosis
Bad sensors, poor electrical connections, or shorted or open wires may all cause the error codes. To prevent further damage to the engine, the code must be addressed as soon as possible. Technicians would use the following diagnostic procedures to diagnose a P1361 DTC code:
- Examine the freeze frame data to see if there are any codes in the ECM.
- Examine the wiring and the Top Dead Center Sensor 1 for any signs of damage, shorting, or malfunction.
- Monitor the signal from the Top Dead Center Sensor 1 to the PCM/ECM to see if it has been interrupted.
- An inconclusive result from these tests can be obtained by using a diagnostic scanner to inspect the signal at the TDC sensor.
Mistakes To Avoid When Diagnosing Honda Code P1361
When diagnosing a P1361 code, technicians often make the following mistakes:
- A lack of thorough inspection of all wiring and connectors.
- TDC sensor signals are not checked.
- The root cause of the code is not properly diagnosed.
How Much Does It Cost To Diagnose Honda Code P1361?
An hour of labor is required to diagnose the P1361 Honda code. A vehicle’s make, model, and engine type all influence the diagnosis time and labor rate for an auto repair. It is common for auto repair shops to charge between $75 and $150 per hour for their services.
What Is The Severity Of This?
In general, the P1361 codes suggest a moderate to severe problem, which needs to be addressed immediately. The vehicle may not start if the problem is not fixed or even damage the engine.
The Bottom Line
For Honda accords, the P1361 code indicates intermittent interruption of top dead center sensor 1. You probably won’t be able to drive your car properly if this sensor malfunctions.
Ensure that the car runs well before clearing the code and reapplying it if the problem persists. Honda vehicle will set and store OBDII fault code P1361 if the TDC sensor fails.
Leave a Reply