Cupholders can sometimes be a nuisance in your car, so removing them quickly and efficiently is essential. You’ll need to remove screws on the inside of the cupholder before you can get it off.
It’s easy to remove the cupholder trim. Taking it off without removing the shifter trim first is possible, but it is a lot more complicated, especially if this is your first time. The shifter surround must be removed first with a flathead screwdriver; then, the cup holder must be lifted gently.
How Do You Remove The Cup Holder On A Honda Accord??
A Honda Accord’s center console can be removed in the following way:
You can pull out the cup holder/cover by grasping it. Clips are holding it in place. The trim around the shifter has to be removed (automatic; I’m not sure about the stick).
The top of the console’s trim needs to be pulled up. It is also held in place by clips. To remove the ashtray from the console, use a pry tool.
You will be able to see two Phillips screws. The trim around the gear selector can be loosened by unscrewing and removing them. The trim can then be removed with your pry tool.
Two screws are located on the front (that hold the tray in place), and two more are located on the back (behind the shifter).
Please remove all of them. After removing that plastic cover, remove the two screws from the storage compartment.
There will need to be some plate removal over the tray (with power outlet; under the radio) due to its four clips holding it in.
The screws under it hold the panels under the steering wheel and glove box (one screw on each side).
To remove the fuse panel access covers, open up both doors, remove the two screws on each side, and then remove the fuse panel access panels. Remove the two panels.
In the very center (very front) of the console, there will be two screws that need to be removed. After removing these two screws, you should be able to remove the console.
To remove it, you’ll have to play with the shifter and parking brake to maximize your available space.
The cup holder compartment can be removed by raising the parking brake handle. A little jiggling will cause it to come loose. It’s held in with clips.
Remove the two screws in the bottom of the compartment by opening the center armrest.
Put the gear shift in P by unlocking the manual release. The entire center console can be lifted around the gear lever and handbrake.
Remove Cupholder
On a Honda Accord, remove the cup holder by popping off the cover and pulling it out. You may also need to unsnap and unclip the cup holder to remove it from its mountings.
If you have trouble removing or replacing the cup holder, consult an authorized Honda dealer for assistance. Ensure your hands are clean before attempting this task; dirty fingers could damage your car’s interior surfaces.
After removing or installing the cup holder, wipe down all surrounding areas with a dry cloth to avoid water spots and fingerprints.
Remove Screws
Remove the screws that hold the cup holder in place on a Honda Accord. Use a Phillips head screwdriver to remove them from the bottom of your car’s dashboard.
Once they’re out, use your hands to pry up on the holder, which will come off quickly. Save time by doing this before you go out for coffee – no more spilling drinks all over yourself. Make sure you replace any screws that are lost during removal – they can be challenging to find.
Raise the Parking Brake Handle
First, to remove the cup holder on a Honda Accord, locate the parking brake handle. Open the driver’s side door and move the seat to one side so you can see behind it. Pry off either end of what looks like a trim piece of plastic with a small hole in it.
The retaining clip should now be easily accessible – use your fingers to pry it off completely. Carefully pull up on both sides of the wire cover until they release from underneath.
Remove Clip
Open the glove box and locate the clip that attaches the cup holder to the center console. Grip one end of it with a hand and pull up while simultaneously pushing down on the other end of the clip to remove it from its socket.
Repeat this process for each side of the cup holder. Be careful not to lose any screws or hardware in the process – they’re invaluable when reinstalling your holders later on. Now you’re ready to install your new holders – consult Honda’s online manual if you need help correctly.
How do you remove the cup holder on a 2003 Honda Accord?
To remove the shifter trim, pop it off by pressing down on one end and pulling it away from the car. The cup holder trim can be removed with your hands if you wedge a flat object between the trim and the side of the vehicle.
Remove the cup holder from behind the seat by grasping onto either side of it and pulling it outwards. Replace the cupholder trim by unscrewing its two screws, then sliding it over to cover up any unsightly marks left on your dash caused by removing the old one.
To Recap
If you have a Honda Accord and want to remove the cup holder, there are a few different ways that you can do it. The easiest way is to use a screwdriver or wrench to take out the screws on the top of the cup holder.
Once those are removed, you can pull off the entire cup holder. Another method is to remove one of the two screws near where your car’s power outlet is located and then pull up on that portion of the cup holder until it pops off.
If neither of these methods works for you, you may need to call an expert.
Also Read – How To Unlock Honda Civic Door?
Leave a Reply