To start a car, an electric current is delivered to the ignition by the spark plugs. In the event that they were not functioning properly, your car would not start.
In comparison to most other car parts, they require very little maintenance. According to Honda, spark plugs should be changed every 30,000 to 40,000 miles.
Your Honda model and make, as well as your driving habits and average driving conditions, will determine how often your Honda should be serviced. You can find this information in your Honda Civic’s owner’s manual if you’re unsure.
You can have trouble starting your car if your spark plugs are faulty, as faulty spark plugs compromise the entire ignition system. In order to keep this crucial system functioning properly, every Honda driver should ask: When should I change my spark plugs?
Check the spark plugs regularly to make sure there is no obstruction and that your engine is running smoothly. If the plugs are fouled or worn, replace them as soon as possible.
How To Change Spark Plugs 2012 Honda Civic?
The HT leads on the spark plugs should be removed from their housings. Taking them out shouldn’t require much force. Grab them as close to the casing as possible and lift them out without pulling them by the leads.
Pro Tip: Replace your spark plugs one by one. As a result, you will be able to tell which lead goes to which spark plug without getting confused. Misfiring can occur if you make a mistake here. It would be helpful if you put a sticker on each HT lead so you will know where each one sits if you are removing them all at once.
Step 1
Removing the old spark plugs from within the engine requires the use of the 5/8 socket head. Don’t force them as this could damage their threads or cause them to break.
Get a flashlight and check around the plug base for dirt and debris before you remove it. If you find anything, clean it up. It is important that none of this gunk falls into the engine when you are removing the plug. All it takes is a little compressed air to throw out any gunk.
Step 2
After removing the spark plug, measure the distance between its points. By doing so, you’ll be able to determine how badly worn they are. Your car’s manual will tell you what the ideal distance between the two points is, if not, search online.
It’s always better to replace them if the gap is okay, but it’s not always necessary. Spark plug gap tools can be purchased online for very cheap, and I recommend that everyone owns one.
Step 3
Put some copper grease or anti-seize on the threads of the new spark plugs before installing them. The next time you need to change them, you will find it much easier to get them out this way. Wipe away any excess that’s on the plugs and be sparing with it.
Step 4
The new plugs should be inserted into their housings and tightened. Be careful not to over tighten them. It can also lead to them breaking or making it impossible to remove them in the future.
Step 5
The HT leads should be reattached in the right order. You should only need to press them into place with a minimum amount of force. To prevent any misfires, make sure all of them are in contact with one another.
Final Step
Check if the car fires properly by starting it.
Check the Spark Plugs
If your car has recently been serviced or you have replaced the spark plugs, now is a good time to check them. Use a plug wrench to remove the old plugs and replace with new ones.
Be sure that the gap between each plug is about .025 inches (6 millimeters). Reconnect the wires by following their colors from left to right and putting them in the correct positions on the plug connector block..
Replace any damaged electrical connectors and tighten any screws.
Change If Worn or Fouled
If the spark plugs look worn or fouled, it is time to change them. Use a replacement tool that fits your car and remove the old ones. Clean off all of the deposits on the electrodes with a wire brush before re-installing them into your engine chamber.
Make sure you use new electrode wires if installing new spark plugs, as these can heat up and cause arcing during combustion. Follow instructions for installation of new spark plugs in order to achieve best performance from your Honda Civic
Disconnect the Battery Cable
To disconnect the battery cable, it is necessary to remove both the negative (-) and positive (+) cables from the battery. Next, locate the two clips that hold each end of the cable in place.
Press down on each clip until it pops out of its hole; then pull both ends of the cable off of the battery. Finally, reconnect each end of the new cables to their respective clips on either side of the battery and tighten them into place with a wrench or pliers.
Remove the Front Wheel Bearings and Hub Caps
The procedure of removing the front wheel bearings and hub caps is fairly straightforward on a 2012 Honda Civic. You will need to remove four screws that are located near the center of each wheel well, then pull up on the lip beneath them to release the bearing assembly.
To take off the hub cap, you’ll first need to loosen its retaining bolt with a wrench and pry it off from the axle using a flathead screwdriver or socket tool. Now you can lift out both bearings and retainers by gently pulling them straight up from their sockets while holding onto one end of each bearing (the race).
Once everything has been removed, clean all parts thoroughly with soap and water before reassembling in reverse order.
Remove the spark plugs using a wrench and screwdriver
Removal of the spark plugs is an essential part of car maintenance and should be done according to your Honda Civic’s owner’s manual. A wrench and screwdriver are necessary tools for this process, which takes around 10 minutes depending on the model of Honda Civic you own.
Be sure to remove all six plugs before replacing them in order to avoid any possible engine damage caused by improper installation or over-tightening of the screws. Always use a quality spark plug socket, ratchet and extension when removing or installing these plugs in your Honda Civic.
What Is the Spark Plug Gap on a 2012 Honda Civic?
Honda Civics manufactured in 2012 require a different spark plug gap size than older models. You can fix the gap yourself or leave it to a mechanic, depending on your car’s age and model year.
Pre-gap refers to the distance between your spark plugs and engine block; if you have an older Honda Civic, it may be time for a new set of spark plugs. If you experience misfires or poor performance, replacing your spark plugs could be the solution.
Can I Change My Spark Plugs Myself?
You can change your own spark plugs on most engines if you have the right tools and a little knowledge about how an engine works. Disconnect the battery cable, ground it out, and remove the ignition coil before beginning.
Unbolt and remove the spark plugs from the engine (wear gloves). Locate the correct compartment in your car or truck, disconnect the wire harnesses, and lift off the cover plate to get at the spark plug wires. Reconnect all of these connections after replacing each spark plug.
How Many Spark Plugs Are in a 4 Cylinder Honda Civic?
To change a spark plug in a Honda Civic, first twist the plug out of its socket and carefully pry off the old one with a wrench. Next, install the new spark plug by hand or using an appropriate tool.
If any gaskets were damaged during removal and installation, replace them before re-installing the engine cover assembly. Be careful not to lose any screws as you work.
How Much Does It Cost to Change Spark Plugs on a Honda Civic?
Honda Civics typically have spark plugs that need to be replaced every 60,000 miles or 6 years, whichever comes first. The average cost of a Honda Civic Spark Plug Replacement is around $150-200 depending on the location and model year of your car.
You’ll also likely incur labor costs associated with this repair – estimate around $50 per hour for a typical job. Tax and fees can add up quickly if you’re replacing your spark plugs on a Honda Civic – plan on spending at least $120+. Be prepared for an estimated range of prices when getting spark plug replacements done – anywhere from $60-$220 is common.
FAQ
How often should spark plugs be changed in a Honda Civic?
Honda Civics typically last for up to 100,000 miles with proper care and maintenance. When your Honda Civic’s engine starts not firing on all cylinders or has a “check engine” light on, it’s time to change the spark plugs.
How often do you change spark plugs?
If your car’s Check Engine Light comes on, it may be a sign that you need to replace your spark plugs. Replacing the spark plugs won’t fix a bad fuel system – too much carbon deposits can cause this problem in the first place.
Checking for worn or faulty spark plugs will help identify an issue with performance early on before it becomes more serious. .
How much is a tune up on a Honda Civic?
Honda Civics can last for many years if taken care of properly, but they do need regular tune-ups to keep them running smoothly. The cost of a Honda Civic Tune-Up varies depending on the work that is done and the make and model of your car. Don’t forget to correct the time on your Dashboard.
How much are spark plugs for a Honda?
Honda engines use spark plugs to ignite the fuel/air mixture in the engine. The average cost of a set of Honda spark plugs is $48-$60, and labor costs typically amount to around $48-60 per job.
To Recap
Changing spark plugs on a 2012 Honda Civic is an easy task that can be done by anyone with basic automotive knowledge. Before starting, make sure to disconnect the battery and use a wrench to unscrew the ignition coil cover.
Once the plugs are out, just replace them with new ones and screw back in the cover.
Leave a Reply