Have you been looking for Honda accord rear spoilers? To feel complete, cars sometimes need a finishing touch. So, if you’re looking to improve the look of your Honda Accord, then adding a spoiler might be just the thing.
Adding a spoiler to the trunk of your Honda Accord would make it look sleek. You will not only be able to give your vehicle an aggressive look, but you will also be able to supplement the traction and handling of your vehicle on the track with the extra downforce it provides.
Many aftermarket spoilers are available for the Honda Accord, all of which follow similar instructions. The following DIY guide will show you how to install a spoiler on your Honda Accord.
How To Install A Spoiler On A Honda Accord?
A Honda Accord spoiler is a part attached to the vehicle’s rear that prevents air from passing over it as it moves, thereby increasing its aerodynamics. To increase fuel efficiency, less drag must be achieved. The materials needed for this project:
- A Honda Accord spoiler kit
- The drill punch and the drill
- Drill bits in 8mm and 10mm
- Screwdriver with a flat head
- An ink pen with a felt tip
- Putty for cleaning
- Hand pliers
- Zip ties
- Tool for removing trunk springs
Step 1 – Take Off The Trunk Liner
The spoiler mounting locations on Honda Accords without a factory spoiler have rubber grommets. You will be able to see the pilot holes once the trunk liner is removed.
- Battery negative (black) terminal should be disconnected.
- Remove the clips around the trunk liner with pliers by opening the trunk.
- The liner should come out easily.
- Under the trunk lid, locate the rubber grommets and remove them.
- Drill a hole in the rubber grommet area.
Step 2 – Drill Holes For Mounting Bolts
Through the punch marks, drill holes with an 8mm drill bit. The drill should be held straight and steady at all times. The protruding metal should be removed with pliers before cleaning off the holes.
Step 3 – Locate The Wire Harness
- From the spoiler kit, grab the mounting template.
- It should be placed over the edge of the trunk lid so that the template holes align with the holes for the mounting bolts.
- Mark two additional holes through the mounting template on the trunk lid with a felt tip pen.
- The mark closest to the rear windshield needs to be drilled with an 8mm hole. A mounting bolt will be inserted into this hole.
- A 10mm hole should be drilled through the mark closer to the rear of the trunk lid. The wire harness goes through this hole.
Step 4 – Put The Spoiler On
- Clean the drill holes with cleaning putty.
- Ensure the spoiler is lined up over the holes for the mounting bolts.
- Through the 10mm hole, snake the spoiler’s wire harness.
- Ensure the spoiler’s bolt holes line up with the mounting holes on the trunk lid.
- The spoiler should be fastened with three 8mm bolts. Make sure the bolts are snugly tightened.
- The spoiler should now be mounted on the other end.
Step 5 – Change The Trunk Springs
Trunk springs manufactured in the past were designed to handle a specific trunk weight. To accommodate the extra weight from the spoiler, they must be replaced with heavy-duty springs.
Use a trunk spring tool with an open end under the upper trunk spring and a closed end attached to the lower trunk spring.
To safely remove the spring, pull up on the trunk spring lever. Then, in reverse order to the removal process, install the new heavy-duty trunk spring with the trunk spring tool.
Step 6 – Install The Spoiler Wires
- Pry off the rear trim panel of the trunk lid with a flathead screwdriver.
- After that, remove the floor panel on the trunk side.
- Through the trunk lid holes, route the wire harness.
- Zip ties should be used to secure the harness to the trunk hinges.
- The harness should be connected to the brake light plug.
- Connect the battery and reinstall the trunk components.
Spoiler Modifications For Honda Accord
Is your car in need of modification? It’s only a matter of deciding where you want to start. You can drastically change the appearance of your car by installing a spoiler. An aggressive, race-ready look can be achieved with a front lip spoiler, a rear window spoiler, and a rear deck spoiler.
Here is a breakdown of costs, installation times, and difficulty levels associated with spoiler modifications. Of course, you can always visit a professional shop if you aren’t familiar with mods.
The aftermarket body accessory market for Honda Accords from 1990 to 2002 is massive, and while spoilers from different brands may look the same, they may differ in quality.
There is a good chance you will find something you can imagine in the Honda aftermarket world if you can imagine it. After that, it is only a matter of imagination and, of course – the budget that limits you.
Rear Deck Lid Spoilers
Many rear spoilers are available on the market, so it’s hard to narrow them down. Lip spoilers, factory-style spoilers, JDM spoilers, and racing-oriented pedestal spoilers are all available.
The replacement OEM spoilers can cost upwards of $400, depending on what look you want to achieve, how discreet you want to be, and what budget you have. These will require drilling straight into the trunk lid to be installed.
Roof And Rear Window Spoilers
A roof and rear window spoiler are the lip between the roofline and rear windshield. Their popularity grew as more rally and endurance racing cars were converted to use on the street. They channel airflow into the boot or rear deck lid spoiler if installed.
Front Lip Spoiler
You can lower the stance of your front end by installing front lips and creating a more aerodynamic appearance. However, spoilers made of carbon fiber are more expensive than polyurethane lips.
Discussions about Spec-D brands can be found all over the Honda-tech community, and many Accord owners seem to like them. However, drilling is usually required for mounting, and painting the body may be required.
Final Words
You can have a lot of fun customizing the outside of your Honda. Various exterior accessories are available on the market for customizing and personalizing your vehicle.
People pay a lot of attention to spoilers regarding the outside of their cars. Sports cars originally used these exterior modifications, but now they are also popular add-ons for everyday rides.
Spoilers increase a vehicle’s grip on the road by increasing the surface area. A vehicle close to the pavement is due to its weight.
Spoilers were invented because they improved a vehicle’s grip and handling without adding much weight. Their purpose is to generate a downward force on a car’s body, like airplane wings, but upside down.
A sporty look is also added to the outside of a vehicle, which changes the appearance of your Honda. To make your Honda look more unique and seamless, add a spoiler, and change its exterior appearance.
Leave a Reply